Switzerland. Existing homes, with administrative questions referred to the canton.
From screening to follow-up
- 01
Locate
Map and rooms involved
- 02
Measure
Recognised service and timetable
- 03
Coordinate
Report, works and follow-up
In this guide
Start with how each room will be used
You are considering a home office on a lower floor, a purchase that includes a bedroom at garden level, or replacement of a floor in contact with the ground. Before fixing the design, mark the rooms people will use regularly and those that touch the ground on a cross-section of the building. Radon is a naturally occurring radioactive gas that can enter buildings from the soil. The Swiss Federal Office of Public Health (FOPH) recommends considering protection from radon when planning renovation work. Start with practical questions. Which room is involved today, how will people use it once the work is finished, and is there already a measurement relevant to that location? Label a storeroom and a proposed bedroom separately when you brief the professional assessing the building.
Read the map at the right scale
The Swiss FOPH radon map shows the probability of buildings exceeding the reference level of 300 Bq/m³. A percentage shown for an area and a reading in becquerels per cubic metre for a room answer different questions. The former puts the property in its geographical context. The latter describes the room where a detector was placed for the reported period. Record the address you looked up and the date, and label the entry as a map lookup. Even if neighbouring houses fall in the same area, keep their measurement reports separate. For your project, knowing which rooms were measured, under what conditions and for how long gives you better questions to ask than comparing the colours assigned to different municipalities.
Review the measurements already available
Ask for the full report if the seller or owner says the building was measured previously. Look for the measuring service, the start and end dates, the rooms assessed and what they were used for at the time. For a house renovated in stages, put the report and the work on the same timeline. Discuss a reading taken before a change in ventilation, a floor alteration or conversion of the basement with a specialist, especially if a different room was measured. When you share the report, attach a marked-up plan and flag any room that will change use. If a page is missing or a room name is unclear, write the question down and ask the measuring service to clarify it before relying on that entry. Ask whether the floor plan has changed since the previous reading. If you have several reports, organise them by measurement period and floor. That lets you point the specialist to the record most relevant to the work under discussion and explain where the old room names differ from the current plans.
Allow time for a recognised measurement
For a recognised measurement in a dwelling, the FOPH specifies at least 90 days during the heating season, from October to March, and recommends measuring for a year. It calls for at least two separate, regularly occupied living spaces, preferably in contact with the ground or on the lowest occupied floor. Where appropriate, it also recommends an extra reading in a basement room with high potential for radon, such as a cellar with an earth floor. Choose a service from the official list and agree on the timing, rooms and detector placement. Allow for access at the beginning and end of the campaign and time to receive the report. Discuss building work that would fall within the measurement period before the equipment is put in place.
Distinguish a quick check from a reference result
When a property decision comes before a long campaign could be completed, the FOPH describes a short measurement that can estimate the likelihood of exceeding the reference level in the building. It is not a recognised measurement and does not estimate the annual average. Write down the question that the short measurement is intended to help answer. Ask the service what limitations will accompany the result and when a recognised campaign could follow. In a shared project file, keep the measurement report, the professional interpretation and your decision about the work separate. That makes it easier for another contractor or consultant to understand several months later what was examined and which points were still open when decisions were made.
Coordinate the assessment and the building work
In an energy retrofit, the FOPH draws attention to components in contact with the ground as well as those exposed to outside air. Ask the design team to mark the relevant walls and service penetrations on the drawings. Share the report with whoever coordinates the work and, if needed, with a radon consultant. Agree on when technical decisions are due and what to record before building elements are closed up. If a protective intervention is planned, include a post-work check in the schedule and name the person who will commission it. Keep drawings and site notes alongside the measurements. Where the finished work differs from the plans, a dated note will help the next person prepare the follow-up check.
Bring questions that lead to decisions
Before speaking to a recognised service, gather the plans, current and proposed room uses, any earlier report and the planned dates for the work. Start with questions that may change your timetable. Which rooms should be measured, when should the campaign begin, when will the report be available, and who can interpret it for the project? If several people are involved, give each one a clear task, such as arranging the measurement or distributing the revised plans. If a result raises concerns, ask the specialist what should be checked before choosing a remedy. Consult the cantonal radon contact if an administrative point needs clarification. File dated copies of the answers so later decisions can be traced to information that can still be checked.
Editorial checklist prepared with AI assistance. General guidance; technical, legal and financial points need individual verification.
FAQ
Does the map give the reading for my home?
It shows a probability for the area. Arrange a measurement in the building.
Can a short test establish the annual average?
A short measurement is a screening tool. The measuring service can clarify the timetable for a recognised measurement.
Compare your renovation quotes with the free sheet ↗
Your question, our next article?
Ask about this topic. Selected questions may become articles or FAQ updates without publishing your email. Avoid confidential information.
